Delivery to any location within 50 miles of our store!

Brands

Newsletter

Subscribe to our newsletter for periodic updates and valuable coupons.

Email Address:
HTML   TEXT-Only

Testimonials

Great

This is just a test submission to show you how it looks, great, eh?
Read More ->



Monochem 200



Call for Price

  • Model: mon.1200
  • 100 Units in Stock
  • Manufactured by: Monochem



PRODUCT DESCRIPTION:
Monochem 200: is a unique two component water borne epoxy resin. It has been modified with a special activators which are reinforced with non toxic color stable and weather resistant pigments. It is formulated to have out standing adhesion while demonstrating high resistance to chemicals,water and impact.

Monochem 200 doesn't contain toxic fumes or solvants. It is recommeded as and interior all purpose, user friendly, Architectural, industrial/Residential, insitutionl and transportation maintance coating. Monochem 200 is for interior use only. It is not UV Stable and should not be exposed to direct sunlight.

It is recommended as an interior all purpose, user-friendly, architectural, industrial/residential, institutional and transportation maintenance coating can be applied on concrete and masonry, metal (plain or galvanized) and wood. Common applications include machinery rooms,warehouses, factories, auto repair and residential garage floors It has ZERO VOC. It conforms to the U.S.D.A. requirements for coatings in contact with food.

It is two-components with a 1:1 Mixing volume ratio. It is packaged in a clear base or white base. It may be tinted with universal colorants to match any color. is available in gloss or low-gloss

PREPARATION:
surface preparation is critical to product performance. Surfaces to be coated must be dry and clean, free from all dirt, dust, oil, grease, wax and loose materials or contaminants. Bare concrete surfaces must be fully cured, porous, structurally sound, and free from rock pockets, voids and cracks. Dense (non-porous) concrete should be primed with,Monopole 2121 sandblasted, shot blasted, or acid etched (2-3 times) to achieve a 120 grit feel for proper penetration and adhesion •Remove all loose, peeling or poorly bonded paint.
•Surfaces must be mechanically abraded using 60-80 grit sandpaper.
•Clean surfaces by using a solution of ½cupTSP to one gallon of warm water. Pay special attention to areas where build-ups of dirt, grease and oil exist. These areas should be scrubbed clean
•Dull glossy surfaces by sanding or by using a chemical deglosser.


APPLICATION REDUCTION AND CLEAN UP:
Mix at a 1:1 ratio: 1-gallon of Part A to 1-gallon of Part B. Stir Part B well before adding to Part A. Mix with a low speed mixer for 2-5 minutes or with a stir stick for 5-10 minutes, scraping the bottom and sides of the container. Mix only an amount of material that can be used within a 3-hour period. Mixed material must be discarded after 3 hours.

Monochem 200 is for interior use only. It is not UV Stable and should not be exposed to direct sunlight. At 77 F will dry in 3 hours. Wait approximately 24 to 48 hours for light foot traffic use, 72 to 96 hours for heavy foot traffic, and 5 days for vehicle exposure. Full cure requires 14-days.
Deep or dark colors made from a clear base should always be used with a pigmented primer or when applying over drastic color changes.
Clean tools and equipment with soap and water immediately after use. Dried material will require a strong solvent, paint thinner or stripper to remove. is useable for a 12-month period stored at roomtemperature (72°F) in a sealed container.
All Monopole floor coatings exposed to water, oil, grease, or any liquids may create a slippery surface. Monopole Inc. will not be responsible for injury caused in a slip or fall situation. It is the end users responsibility to determine the suitability and safety of our coatings for their particular use and application.

•Do not apply over poorly-bonded paint.
•Do not apply if moisture in the substrate is higher than 15%.
•Do not apply to a surface exhibiting hydrostatic pressure.
•Do not apply if surface temperature is over 90°F. or below 55°F.
•Do not apply if surface pH level is above 8.
•Do not spread the coating too thin over an entire area and allow it to dry hard before applying a 2nd coat is applied at the approximate spread rate of 250-300 square feet per gallon, yielding 2-3 dry mils of thickness per coat. Two coats are required. Additional coats may be required, depending on intended use, surface porosity and texture. apply the second coat 2-4 hours (not to exceed 24 hours) after the first coat, while the first coat is still tacky. Silica sand #30 or #60 may be added or broadcast to create a non-skid finish. is applied at the approximate spread rate of square feet per gallon, Two coats are required. Apply a medium to heavy first coat then allow a two minute setup time before back rolling all rundowns in the same section. Allow 2-4 hours dry time before applying a second coat. . Monochem 200 is available in a clear base and white base that can be tinted with Universal Colorants. Tint only Part A; Part B cannot be tinted. The Part A is short-filled:

ADDITITONAL DATA:
MONOCHEM 200 qualifies for earning LEED® credits for Indoor Environmental Quality, EQ 4.2 Low-Emitting Materials, based on low contribution of VOC. ALWAYS apply a test patch to check for coverage rates, adhesion, compatibility and for desired results. Responsibility for determining the adhesion and coverage of to an existing finish rests with the applicator. Applying over existing and poorly adhering painted surfaces may result in the eventual lifting of the old paint CHEMICAL RESISTANCE OF MONOCHEM 200 PER ASTM D 1308 24 HOUR EXPOSURE Gasoline.........................................................................No Effect
Motor Fluid......................................................................No Effect
Transmission Fluid............................................................No Effect
Mineral Spirit...................................................................No Effect
Brake Fluid...............................................Slight Softening, Film Recover
Skydrol LD4..............................................Slight Softening, Film Recover
10% HCL ........................................................................No Effect
10% Nitric.......................................................................No Effect
28% Sodium Hydroxide......................................................No Effect
10% Sulphuric Acid...........................................................No Effect
10% Hydrochloric Acid.......................................................No Effect
10% Acetic Acid...............................................................No Effect
2% Aqueous Pine Sol........................................................No Effect
40% Cleaner Concentrate..................................................No Effect
DI Water.........................................................................No Effect
Urine..............................................................................No Effect
Coffee............................................................................No Effect
Vegetable Oil..................................................................No Effect
5% Tide.........................................................................No Effect


MSDS's are available upon request.

For Product delivery greater than 60 miles from the San Fernando Valley California please contact us for shipping information

You can also visit our library of references and helpful tips at our wood finishing Blog at: www.woodfinishings.wordpress.com


Copyright © 2018 Annex Paint and Lacquer
Powered byZen Cart|  Developed by:IDEAS Creative Group

SSL  Authorize.Net